** **

# Units of measurement, the format of the values.

Under the format refers to a numeric format, which displays the units of measurement of various parameters of a car. Deg minutes. Deg with шестидесятеричной=- (0 degrees 30') 1° 01' 1 ° 05' minutes of the 1st 01' rounding up to the nearest 1' minutes of the 1st 05' rounding to the nearest 5' Deg decimal. Deg with decimal fractions- (0,50 °) 1.01 ° 1,01 ° decimal 1.01 rounding to the nearest 0.01 decimal 1.05 rounding to the nearest 0,05 decimal 1.1 rounding to the nearest 0,1 decimal 1.25 rounding to the nearest 0,25 Deg fractional. Deg with ordinary fractions - (1/4°) 1 b/GE° b/GE, b/DC, d/GE, b/BG 1 b/GE° b/GE, c/GE, d/GE, e/GE 1 b/DC° b/DC, b/BG, d/DC, the b/l 1 b/DC° b/DC, c/DC, d/DC, e/DC 1 b/BG° b/BG, b/l, d/BG, b/E 1 b/BG° b/BG, c/BG, d/BG, e/BG a 1 1/4 a 1 1/8
the 11/64 rounding to the nearest 1/64 When you select a format, the fraction may be reduced or not reduced, i.e., brought or not, refer to the lowest common denominator: condensed fractions 1/16, 1/8, 3/16, 1/4 ...
Units of measure and size of linear values. Inches (Inches). Inches to decimal fractions - (0,25") 1.01" 1,01" Inches from ordinary fractions - (1/4") 1 b/GE" b/GE, b/DC, d/GE, b/BG 1 b/GE" b/GE, c/GE, d/GE, e/GE 1 b/DC" b/DC, b/BG, d/DC, the b/l 1 b/DC" b/DC, c/DC, d/DC, e/DC 1 b/BG" b/BG, b/l, d/BG, b/E 1 b/BG" b/BG, c/BG, d/BG, e/BG a 1 1/4 rounding to the nearest 1/4 a 1 1/8 rounding up to the nearest 1/8 the 1 1/16 rounding to the nearest 1/16 the 1 1/32 rounding to the nearest 1/32 the 1 1/64 rounding to the nearest 1/64 When you select a format, the fraction may be reduced or not reduced, i.e., brought or not, refer to the lowest common denominator: condensed fractions round of 1/8, 3/16, 1/4...
The measurement units of the metric system in millimeters (mm). 1.1mm The base, and the reference diameter of the disc. If as a unit of measurement is set to inches or millimeters and a reference diameter, the system uses the value of the reference diameter specified in the specification of the vehicle . American standard. If the units are installed inches or millimeters, the default base diameter of the wheel is considered to be equal to the reference value 28,648 inches, which is a simple restatement of 2 The european standard. If the units are installed inches or millimeters, the default base diameter of the disc is equal to 14 inches, which is a simple restatement of 20 mm on the European standard. The japanese standard. If as a unit of measurement established correlation inches or millimeters, which is a simple restatement of 0 degrees 05' to 1 mm on the Japanese standard. The actual value, enter the diameter of the disc. If as a unit of measurement is set to inches or millimeters base diameter of the disc, the system uses the value of the base diameter of the disk specified in the specification of the vehicle, or the value entered in manually. To call data of the car during the measurement program asks for the actual diameter of the disc. In this case, the data and results will be translated on the basis of the entered values. The choice of format. The choice of format is carried out on the basis of a suitable example. For each parameter you can select only one of several formats. All possible options are listed in the table below: (see table 12). 110). tab. 110 Format Specification. The specification of the convergence angle of the different formats for one car Lada (VAZ) : 1200/1300/1500/1600: 1974-83, All the possible options are listed in the table below: (see table 12). 111).
tab. 111 Specification in different formats. |